Replaced motor now it will start and tun but put it in gear and it firs

I was driving down the road and it died on me. Basically if the starter motor is turning the engine over rapidly at sufficient RPM but the engine does not catch and run that means that there is an ignition fuel air induction or mechanical fault in the engine that will have to be repaired.

The truck now wont start not even make a attempt no click or nothing Ive replaced the starter igntion switch relay.

Replaced motor now it will start and tun but put it in gear and it firs. And an air filter. And yet the truck still hesitates and now it dies in gear. It throws code p1351 I have changed all parts known to fail with that code and yet the truck still runs rough.

And on cold start the truck will only turn on with starting fluid. Im not sure whats wrong with it anyone have an idea. The starter motor is not easily accessible.

Depending on the car you are driving you may have to remove other engine parts to access it. You should take the intake manifold out then run the following checks on your starter motor. Tighten the mounting bolts and other connecting wires.

Motor wont go in gear after replacing water pump you disconnect cabe where it attaches to the shift linkage and manually shift it. Also if trying to shift without the motor running someone needs to turn the prop when shifting so that the clutch dog gears line up. Try this first if.

The starter solenoid is located on top of the starter. When you turn the key it is the starter solenoid that pushes a plunger inside the starter motor pushing the pinion towards the flywheel. Use a jumper wire to ground the solenoid to a bolt.

Discussion Starter 1 Apr 29 2009. Hey all I appreciate any ideas you all have because I am at a total loss here. My bike is a 2000 R1.

The bike will only start in neutral with the clutch in now. When I put the bike in gear it just dies immediately. You can hit the start button and the engine rolls over and over but will not fire.

Now put it into reverse and it should lock to the right and racket left. If this does not happen then you got the splines off by one or two splines. Now even if the shift was off and as long as the motor cranks it will not have any bearing on weather or not the engine starts.

It may be harder to start because prop may be turning. Starter Your starter may be loose so make sure it is bolted in place. Injectors A bad injector can keep the engine from firing.

Cold Start Valve If the engine is cold and the cold start valve is bad it can keep your car from starting. Flywheel or Ring Gear Worn teeth on these gears can keep your car from starting. I havent hand cranked the engine Im not sure how honestly.

My truck has a 302 v8. An older version though. To rotate the engine by hand after setting the trans in neutral I place a breaker barsocket on the crankshaft bolt and turn it in the same direction it turns with the starter motor.

Not supposed to turn the engine backwards. Very good infoI replaced a timing belt on a 1997 avalonAfterward car starts runs for a minute or two then diesIT would not start immediately afterNext day it would start normally and then dies suddenly about a minute or two after startBefore replacing timing belt car was running greatChanging timing belt was preventative maintenance. Symptoms of a seized engine.

If you have an electric starter your engine will not even turn over. Your starter will make a brief clicking noise then make a humming sound. Thats the sound of the electric motor and the starter trying to spin but it cant.

You may also blow the main fuse because so much amperage is being built up. BMW may start fine when cold but if it warms up it will refuse to start. The car starts fine in the morning.

You drive it for 30 minutes or an hour. Turn off the engine. Try to start the engine again but now it wont start.

Any of the following can cause this problem. After this try to start the engine if the light goes off it means the problem was merely in the system security. Evaluate The Injector Pulse.

Injector pulse plays a key role in entering the engine through the injectors. So if there is any problem with the injector it. To reset my TCM I turn on the key to the on position press the gas pedal to the floor for 10 seconds and then turn the key off then release the gas pedal and wait about 5 minutes to restart the engine.

I have a 1999 Chevy 1500 I rebuilt the transmission so when. I have a 1993 chevy k1500 my transmission went out while I was driving I turned it off and back on created in first gear to a stopping point and turned it off. The truck now wont start not even make a attempt no click or nothing Ive replaced the starter igntion switch relay.

And cannot figure out why it wont work. Basically if the starter motor is turning the engine over rapidly at sufficient RPM but the engine does not catch and run that means that there is an ignition fuel air induction or mechanical fault in the engine that will have to be repaired. If there is fresh fuel being delivered by the injectors not just to the injectors and the.

I have replaced plastic FLYWHEEL starter gears several times. And the pinion gear on the starter many times. And if the little pinion gear wont raise up to engage the flywheel RING gear no matter how you position the flywheel ring gear–it is not going to turn the crankshaft to start the engine.

If the starter motor bolts check OK remove the starter and check the pinion gear. If the pinion gear seems in good shape check the teeth at the flywheel ring gear for damage. You may need to use a flywheel turner or turn the crankshaft using a breaker bar to inspect the whole ring gear.

Refer to the section Engine Seize Test below. Step 1 - After a new battery has been installed the engine could idle low or stall out altogether. When this happens hold the accelerator pedal to help engine to continue to run.

This will allow time for the computer to relearn its adjustments this may need to be done until the engine has warmed up to operating temperature and driven awhile the engine should then re-gain its idle properties. The engine will not start either so be sure to put it in the P range when you turn off the engine. Automatic gear shifter on Hyundai Tucson the shifter must be on P for the vehicle to start Dead key fob.

For models that use smart keys the smart keys may prevent the engine from starting. The most common reason is that its battery is dead. On November 03 2016.

I have a 5-Speed 03 Passat. I got it with the clutch sinking to the floor with no resistance which to my knowledge was a master cylinder or slave cylinder failure. I replaced both although it turned out only the slave had failed.

I have since repeatedly bleed the slave cylinder the clutch is now stiff and has resistance. Starter Motor Problems Mercedes wont turn over. If the starter is defective you will not be able to get the engine to turn.

First check the starter fuse. Often times when the starter is defective or seizes up it will blow out the fuse that protect the starter circuit. If the problem is not battery-related you may have a bad starter or even a seized engine preventing the starter from engaging.

After ruling out a bad battery its recommended to have further troubleshooting done by a mechanic. The ATV wont start it just clicks. 2005 Chevrolet Starter Wont Engage Replaced starter and battery.

Car will not start when outside temp is cold. After it warms up it will start and run great. Key turns lights work and all but car will not turn over.

Why does my car. I was driving down the road and it died on me. It would not turn over.

Chevrolet Silverado Blower Module Location. Starter turns when hooking up battery key not in ignition 1994 GMC Suburban K1500 57L 350 4x4. Removed the battery and starter motor.

Bench tested starter motor at local auto parts shop and they said its fine. Battery was shot so I bought new one. Re-installed the starter motor.