Mounting bow mount trolling motor

Engine mount trolling motors are fixed with bolts to the outboard motors anti-ventilation plate. Ive got a 15 ft center console glass boat inshore salt oriented with a bow rail but I also use it for fresh water bass fishing and I want to add a bow trolling motor.

We specialize in bow mount trolling motors for medium to larger freshwater and saltwater fishing boats.

Mounting bow mount trolling motor. Mounting bow mount trolling motor. Lots of different ways to do that. One is pictured below.

Add a small pie shaped piece onto the very front of your boat. Another is to build up the front deck with a couple of pieces of 2x6 stacked on top of each other. Additionally a number of manufacturers make aluminum steps that screw onto the front deck.

Here are the general steps for installing a bow mount trolling motor. Set the motor up on the boat. Make sure the shaft lays and props up correctly.

This is the first and most important step because you need to make sure things line up before making any holes or cuts. Drill the correct mounting holes. Bow mounting of a trolling motor allows effective navigating of the vessel while spending less effort.

One usually installs the main motor on the opposite side because trolling motors are often used when the main motor is switched off. This guarantees silent fishing and allows moving in shallow and weedy places. Bow mount trolling motors are relatively easy to install on boats with flat bows.

All you need to do is to bolt the motors mounting pad to the bow. If your boat has an angled bow or other features that prevent straightforward horizontal mounting you will need to fabricate a plate to which the trolling motor can be attached. There are many ways to mount a trolling motor on your bowrider the simplest and least expensive being the screw-clamp-on-the-bow-rail style.

In this method of mounting the shaft of the motor has a plastic or composite block that clamps onto the stainless steel railing as close to the centerline of the boat as possible. Trolling Motor Mounts Trolling Motor Mounts Old Town Sportsman 106 Mounting Plate 7500 Native Falcon Motor Plate 8999 Bow Mount Trolling Motor Plates 9999 - 15999 OneObjective Shearwater125 Stern Mount. 2599 - 22999 Crescent LightTackle CK 1 Crew Mounting Plates 10000 OneObjective Hobie Line of Mounts 14999 - 16999.

MotorGuide 8M4000873 Trolling Motor Mounting Kit for Bow-Mount Brackets Set of 4 Screws Washers Rubber Washers Nuts 44 out of 5 stars 20 Minn Kota Bracket Hinge Assembly 2771818. We specialize in bow mount trolling motors for medium to larger freshwater and saltwater fishing boats. Were the 1 store for Minn Kota and MotorGuide trolling motors and accessories and our selection includes the best offerings for 12v 24v 36v i-Pilot i-Pilot Link and Pinpoint GPS-enabled products.

A bow mount trolling motor gives a fisherman the most control over his boat while fishing. It pulls the boat through the water and gives better control and maneuverability than one designed to mount on the transom. Any boat 14 feet or longer can accommodate a bow mount though you may have to modify the bow if it.

Use the mount itself as a template for this. 3 Drill the holes for the mounting bolts. Use a drill bit sharp enough and tough enough to drill through the metal of the anti-cavitation plate.

4 Place the mounting bracket on top of the anti-cavitation plate again. 5 Insert the mounting bolts and tighten them. This will secure the trolling motor.

Engine mount trolling motors are fixed with bolts to the outboard motors anti-ventilation plate. The installation process is straightforward. You dont have to modify your boat or add any brackets like its in the case of bow-mount and transom-mount models.

Mounting bow-mount trolling motor Fiberglass tri-hull. May 27 2017 at 741 pm 1696292. Installing a bow-mount TM on my old tri-hull.

The bow has large flat areas on either side of the redgreen nav light plenty of room to install the quick-release bracket. The only concern is that I. Ive got a 15 ft center console glass boat inshore salt oriented with a bow rail but I also use it for fresh water bass fishing and I want to add a bow trolling motor.

This obviously gets in the way of the bow rail. TM operation would be on fresh water lakes only. Anglers Pal 950210 Trolling Motor Mount 10 AluminumBlack.

Minn Kota 3 Raptor Setback Bracket. This Bow Mount Trolling Motor comes standard with a sacrificial anode encapsulated electronics and a wireless hand control which allows you to control your trolling motorboat from as far as 164 feet away. The controller is compact and fits into the palm of your hand optional wired foot control pedal.

Some transom-mount motors have flexible designs and can even be adjusted for bow-mount use. Trolling Motor Accessories Mounting kits replacement propellers and other trolling motor accessories simplify the use and maintenance of a trolling motor so you can focus on the actual trolling. Minnkota offers a trolling motor installation hardware kit that includes well nuts which are rubber isolators with a threaded brass insert.

You drill the hole push in the well nut place the motor or mounting plate over the well nuts and then insert and tighten the bolts. How to mount a trolling motor on an aluminum boat. There are three main ways to mount the motor.

It can be done on the bow stern or engine. Depending on the location you will need to drill holes and screw the base of the motor or attach it to the boat using a clamp. Read on and I will share some tips so you can install a trolling motor like.

New to the whole scene here. I just purchased a Grizzly 1648 MVX. It will have electric motor only as you cant even have a gas one mounted for the reservoirs around here.

I really want a bow mount trolling motor but have a mounting question. On the grizzly I would not be able to get to the underside of the bolts to lock up with a nut.