Installing bow mount trolling motor on aluminum boat

Attach with 316 rivets and back them up with aluminum washers. On the grizzly I would not be able to get to the underside of the bolts to lock up with a nut.

I would suggest you to mount the motor on the transom as it is easy to install as well as to remove the motor.

Installing bow mount trolling motor on aluminum boat. Putting a Minn Kota Powerdrive V2 bow mount trolling motor on an Alumacraft 1860 aluminum jon boat. How to mount a trolling motor on an aluminum boat is very simple. For a transom mount motor after you position your motor correctly you only need to tighten the clamps.

For a bow mount trolling motor you will bolt the motor mount. How to mount a trolling motor on an aluminum boat. There are three main ways to mount the motor.

It can be done on the bow stern or engine. Depending on the location you will need to drill holes and screw the base of the motor or attach it to the boat using a clamp. I would trace out the outline of your bow on a piece of cardboard.

Cut the cardboard outline out longer than you think you want the mounting base then place your trolling motor on top to see how long it needs to be to fasten the trolling motor and cut the final lenght of the cardboard. Take that cardboard back to your boat and make sure that you have enough room. How Do I Mount A Trolling Motor On An Aluminum Boat Dc Installing A Trolling Motor On The Bow Boating And Boat Fishing Surftalk Trolling Motor Mount For Jon Boat Off 73 Medpharmres Com Homemade Trolling Motor Mount Nc Angler Forums Can You Mount A Trolling Motor On The Side Of Boat Anchor Travel.

Then he drilled 3 holes on each side of the V through the 1 wide piece and 3 holes on each side of the gunnel. Then he used some 2 or 25 or maybe even 3 bolts and some nylon lock nuts and fastened it to the front. He then mounted his trolling motor to the new piece.

Works perfect and is very sturdy. Mine uses 4 2x2x116 clip angles riveted to the inside of the wide gunwales yours will rivet to the boat hull and you may want to use 6 instead of 4. The aft section of the deck is supported by the vertical bulkhead with the tm plug and trim controls and is why I suggest you use 6 clips instead of 4.

Attach with 316 rivets and back them up with aluminum washers. Before mounting and drilling stick strips of step traction coveringon the mount so that you have a gasket between the mount and the boatquiets things down alot and keeps it from vibrating loose. Mounting off center on the Port side is the way to go.

The first and foremost thing that you should consider for mounting the motor is that you should know where you can mount the motor on the boat. You can install a trolling motor on the transom the bow and the engine. I would suggest you to mount the motor on the transom as it is easy to install as well as to remove the motor.

Also if you own small. Adding a bow mounted trolling motor. There is also the option of a quick release mount I know minn kota has one.

From that you could add extra bracing if required. Maybe go Gunnel to gunnel with a piece of aluminum angle to pick up the back side of the quick release mount. Dont install it directly over the point of the bow but off to one side approximately a foot from the point.

Position the motor in the deployed or down position to be sure it clears the outer edge of the boat and will lock into place and move in all directions without touching the boats hull. I also had the fishing package installed on my boat so the trolling motor plug is located under the starboard fishing seat. I did have to overhang my MKA-32 quick release bracket a bit over the bow to properly position the motor.

5 out of the 6 mounting bolts were used and the mount. Installing a bow mount Trolling Motor on a boat with a bow rail. Joined Jan 11 2007 1 Posts.

Discussion Starter 1 Feb 12 2007. I want to install a bow mount trolling motor on my boat but it has a bow rail. Can anyone point me to the solution they have used to overcome this problem.

I prefer not to cut the front of the rail out. Mounting bow mount trolling motor on 14 v-hull. By bcbouy 02 Apr 2018 0031.

550 plus 60 canadian for a quick release mounting plate and a hand held remote is includedwith a lion rechargeable battery55 lbthrust and a built in battery gaugehad it for 2 years with no problems whatsoevercould buy 3 of them for the price of the. New to the whole scene here. I just purchased a Grizzly 1648 MVX.

It will have electric motor only as you cant even have a gas one mounted for the reservoirs around here. I really want a bow mount trolling motor but have a mounting question. On the grizzly I would not be able to get to the underside of the bolts to lock up with a nut.

Installing a Bow Mount Trolling Motor My big water boat is an aluminum 14 foot V hull and needs some additions for the kinds of fishing I plan to do. My first article detailed adding the lights and bilge pump this article will detail the installation of the bow mounted. Trolling motor brackets are available to be added to any 3 model boat.

Trolling motor brackets are not needed on 15 models since trolling motors can be mounted on the bow. Part numbers to use when ordering from dealer. 48 52 TM Bracket.

There is a small metal support piece bolted to the very front to secure the transom and give a hand hold as well as house bow light socket. I need a way to mount a Minnkota bow mount motor. I have the quick release bracket so i would be mounting the base of the quick release.

I can see that I need a platform to mount on that will attach to gunnels.