05
Sep
Use a pressure washer to clean the bottom of the boat. Bear in mind that before you leave the motor there there are.
Connect Earmuffs and Warm up the Engine.
How to winterize your outboard motor. Proper winterization protects against corrosion and freeze damage that can occur while your motor is in winter storage. Heres everything you need to know about how to winterize an outboard motor. Change the Crankcase Oil.
If you have a four-stroke engine its important to change the oil before you store your motor for the winter. The oil will be dirty and full of contaminants after summer use and over the course of the winter months these contaminants can corrode your. Fog the cylinders while flushing the motor with antifreeze.
To prevent freeze damage prior to winter storage many owners simply drain the cooling water out of their outboards. However while it might seem like overkill we recommend flushing your motor. During the process on how to winterize an outboard boat motor get the focus you need.
Double check the engine fuel systems plumbing and any other systems that may retain water. Include the suggestions from the websites supplied and consider the manufacturers instructions for winterizing your boat motor via the owners handbook as well. If your motor has a 3-gallon tank pour in about half an ounce and slosh it a little to mix it up.
Adding a bit of extra stabilizer than the usual instruction says wont cause any. Plug in the earmuffs and start the engine Attach a hose to the fluid intake ports on the units bottom and attach a set of flush or earmuffs to them. One of the most important steps to winterizing your outboard motor has to do with the fuel system.
To cut down on fossil fuel usage most fuel you buy these days has some amount of ethanol in it. You can do this on an engine stand or sawhorse at the same time youre flushing the engine. Flush the engine with fresh water.
Using an outboard flusher or earmuffs as some call them put them over the raw water intake of the engine and connect a hose. Turn on the water and start the engine. A small outboard motor must be winterized and then taken inside your storage shed or your garage.
If possible hang it above the ground. If possible hang it above the ground. Bear in mind that before you leave the motor there there are.
Remove the spark plugs and spray the fogging oil directly into the engines combustion chambers. Spray the oil for a couple of seconds into each spark plug hole. Install the spark plugs back into the engine and torque them to the manufacturers specs provided in the outboards owners manual.
Start by making a checklist of all the tasks you need to get to. You can find winterization recommendations from the manufacturer in the owners manual for your motor as well as the manual for the boat itself. If you are a boating amateur it may be best to consult a friend with experience or contract an expert.
Remove the overflow screw and put a container under the drain screw to catch the old oil. Remove the drain screw and washer and let the oil fully drain. Attach a gear lube pump to the drain hole and pump new gear oil into the gearcase until it reaches the.
How To Winterize Your Boat Motor Outboard Type It requires a few steps to get your boat ready for the winter While a majority of steps remain similar for both outboard and inboard motors. Its the few steps and their procedure that sets it apart from the steps followed for the inboard stern type engine. Another important factor when winterizing your outboard motor is to flush it with water.
This will help get rid of any sediment collecting within the system. Hook up a garden hose to a motor flush attachment which will cover the water intake on the lower unit of the motor. Turn on the water and then start the motor.
If you decide not to winterize your outboard motor then you can seriously damage the machine. Poor maintenance is more likely to break your motor than high usage and leaving your equipment salty and wet can erode important parts of the motor. Your motor should be correctly stored and cleaned before any long period of non-use.
Navigate through to winterize mode and click the button Winterize Engine. The winterization process will engage itself a. The engine will double oil itself b.
The engine will run for 90 seconds and then shut itself off. Check to make sure the propeller is free of any device that may be wrapped around it. Its Just That Easy.
How to Winterize an Outboard Motor 4 Stroke Step 1. Clean Your Boat Thoroughly. Start by cleaning your boat inside and out.
Use a pressure washer to clean the bottom of the boat. After cleaning your boat apply a coat of wax on fiberglass hulls. Before starting the whole job check whether you have all the essentials I listed above.
Connect Earmuffs and Warm up the Engine. Attach a pair of ear muffs or flush muffs to the water intake ports on the lower end of the unit and connect it to a hose. Turn the water on and start the engine.
Let the engine warm up for about 5 minutes to treat the entire engine with stabilized gas mix. To keep your outboard motor in top shape from year to year prepare it carefully for winter storage. Owners manual freshwater flushing unit garden hose screwdriver adjustable wrench coffee can or other container tarp piece of scrap wood.
How to Prep Your Outboard Motor for Winter Storage. Here are the steps. Change oil filter.
Prior to winterizing the engine its a good idea to give the boat a good cleaning inside and out power wash the bottom and put a coat of wax on fiberglass hulls.