How to winterize an outboard motor 2 stroke

Using an outboard flusher or earmuffs as some call them put them over the raw water intake of the engine and connect a hose. Using an outboard flusher or earmuffs as some call them put them over the raw water intake of the engine and connect a hose.

For older two-stroke motors you use canned fogging oil and spray it into the carburetors just as the motor idles out of fuel.

How to winterize an outboard motor 2 stroke. Winterizing a 2-Stroke Outboard. Lower Unit Oil Change Mercury recommends the gearcase lube be changed every 100 hours or once per year. However you should do it regardless of how long its been before storing your outboard because harmful contaminants in the used oil can corrode the inside of the lower unit.

Fog the Engine. Remove the engine cover and find the carburetors air intake port. With the engine running spray a small amount of fogging oil into the intake.

The engine will want to die but keep it running by opening the throttle. Continue to fog the engine until it dies. If white smoke comes out of the exhaust youre doing it right.

Make sure to place a drain pan underneath the unit before you begin to take any screws out. Now there will be 2 screws you will need to unscrew in order to drain the oil. The first will be found near the bottom of the skeg you unscrew this one first and oil will begin to immediately pour out.

Winterizing my 2 stroke outboard. Drain the carbs too. Remove the spark plugs and spray the fogging oil directly into each cylinder following the directions on the can.

Let the engine warm up for about 5 minutes to treat the entire engine. Httpbitlytwo-stroke-outboard-winterization-kitWinterizing a 2-stroke outboard motor puts an. Turn the water on and start the engine.

Use EvinrudeJohnson Storage Fogging Oil to prevent corrosion of internal engine components during periods of storage. Remove the air silencer. START outboard and run at IDLE.

Two ounces of EvinrudeJohnson Storage Fogging Oil through the throttle plate hole of each cylinder while outboard is running. Turn key switch to OFF to STOP outboard. How to winterize a 2 stroke outboard motor boats net how to winterize a 2 stroke outboard motor family handyman how to winterize a 2 stroke outboard motor boats net how to winterize a 2 stroke outboard motor family handyman.

Whats people lookup in this blog. Winterize Outboard Motor 2 Stroke. Especially when there is a high chance of snowflakes youll be happy to winterize an outboard motor 2 stroke.

The sooner you winterize boat motors the less likely corrosion can harm them. These are the answers you can find in this article about how to winterize an outboard boat motor. The tools and materials youll need in winterizing boat motors The step-by-step process of winterizing outboard boat motor.

Ideally this is done while the engine is still warm and involves spraying fogging oil directly into each cylinder of a four-stroke engine. If you have a two-stroke engine instead of fogging oil youll use outboard oil but the process is the same either way. 2 stroke engines are slightly more difficult than 4 stroke engines but if you follow the general guide below you wont go far wrong.

Carry out a routine service on the engine This will mean some of the tasks you need to do anyway are done ie. Lubricate all the manufacturers recommended lube points and replace the gear oil. Add fuel stablizer to the existing gas2.

Run for at least 15 min to get the stabilized fuel well into the engineDrain the carbs too. Even if you disconnect the fuel line and let the engine. During the process on how to winterize an outboard boat motor get the focus you need.

Double check the engine fuel systems plumbing and any other systems that may retain water. Include the suggestions from the websites supplied and consider the manufacturers instructions for winterizing your boat motor via the owners handbook as well. For older two-stroke motors you use canned fogging oil and spray it into the carburetors just as the motor idles out of fuel.

This adds the needed layer of oil residue onto all the interior parts. For two- and four-stroke carbureted motors after running the motor for five to ten minutes per the instruction above shut off the motor disconnect the garden hose and hook up the winterizing kit to the flushing muffs. Then fill the winterizing kits tank with antifreeze which should be of the non-toxic propylene glycol variety.

You can do this on an engine stand or sawhorse at the same time youre flushing the engine. Flush the engine with fresh water. Using an outboard flusher or earmuffs as some call them put them over the raw water intake of the engine and connect a hose.

Turn on the water and start the engine. Use engine fogger and spray it into the intake until the motor starts to choke and sputter. Do this 2-3 times.

Remove the spark plug or plugs and spray some fogger into the combustion chamber. Replace the plugs but keep the plug wires off. Turn the motor over 2-3 times to cycle the fogging oil.

You now have a winterized two-stroke outboard. Four stroke outboard motors are by fa. Remove the spark plugs and spray the fogging oil directly into the engines combustion chambers.

Spray the oil for a couple of seconds into each spark plug hole. Install the spark plugs back into the engine and torque them to the manufacturers specs provided in the outboards owners manual. Navigate through to winterize mode and click the button Winterize Engine.

The winterization process will engage itself a. The engine will double oil itself b. The engine will run for 90 seconds and then shut itself off.

Check to make sure the propeller is free of any device that may be wrapped around it. Its Just That Easy. Winterize your Engine in under 2 minutes with a push of.

Another important factor when winterizing your outboard motor is to flush it with water. This will help get rid of any sediment collecting within the system. Hook up a garden hose to a motor flush attachment which will cover the water intake on the lower unit of the motor.

Turn on the water and then start the motor. Run your outboard at normal idle speed for 5-10 minutes to allow the engine to warm upIt is best to use a mixture of stabilized fuel with fogging oil. Follow brand directions and be sure 2-stroke pre-mix models have the appropriate oil also in the fuel.