03
Aug
Run antifreeze through the water intake spray the fogging oil Step 6. Change the Engines Oil.
Add Antifreeze and Spraying Fogging Oils.
How to winterize an inboard boat motor. How to Winterize an Inboard Boat Step 1. Check your manual for special instructions Step 2. Fill the tank with fuel apply stabilizer Step 3.
Let the engine run Step 4. Drain all liquid from the engine Step 5. Run antifreeze through the water intake spray the fogging oil Step 6.
Perform the necessary boat maintenance Step 7. Dry the whole boat. Changing the engine oil and filter is an essential step to winterize inboard boat motor.
The lubricant may already contain unwanted particles that can harm the motor if left to sit throughout the winter. Turn off your engine and locate the engine oil port. Open the port and insert a.
How to Fully Winterize Inboard Boat Motors in 4 Steps Prepare Your Inboard Boat Motor for Winterizing. Fill the tank with gas. Add Antifreeze and Spraying Fogging Oils.
After your motor is cleaned and prepared as described above the first real winterization step is applying antifreeze. Change the Engines Oil and Replace Oil Filter. Do a Final Inspection.
How do I winterize a 2-stroke outboard motor. This is the way I have done it. Change the gear oil in the lower leg.
Run your normal fuel with fuel treatment. Run it dry to empty tank. The fuel treatment will help get rid of any tiny amounts of water in the system.
Pull the spark plugs pour in an ounce of Marvel Mystery oil in the plug holes. If your boat stays afloat all winter you can drain the systems by first closing the seacocks for the raw-water inlets then removing the inlet hoses and intake-pump covers as well as all drain plugs. After clearing the raw-water systems replace all of the drain plugs.
How to Fully Winterize Inboard Boat Motors in 4 Steps Prepare Your Inboard Boat Motor for Winterizing. Fill the tank with gas. Add Antifreeze and Spraying Fogging Oils.
After your motor is cleaned and prepared as described above the first real winterization step is applying antifreeze. Change the Engines Oil and Replace Oil Filter. Do a Final Inspection.
For inboard and sterndrive engines. Flush the engine with clean water by using water muffs or a similar device to connect a garden hose to your cooling system. Never run a water engine without water.
Then flush until the engine reaches normal operating temperature. Next remove drain plugs. These are usually located in the engine block and manifold.
To winterize your boat motor. First place the boat on trailer with muffs on. Fill the fuel tank up to 80 to 90 of its total capacity.
Add fuel stabilizer to the fuel tank and let your engine run for 10 to 20 minutes when you winterize your boat motor. Flush the engine with fresh water. Replying to Topic Winterizing an Inboard engine The fake a lake is like the clamps you were talking about with your IO it is different than the flush kit.
I made my own by taking a plunger and inserting a water hose into the side of the rubber you can then wedge the handle against the ground and have the rubber cup around the water intake. In this case winterize it according to the manufacturers recommendations. Make sure you use propylene glycol antifreeze when winterizing your boats systems.
Antifreeze made with ethylene glycol is highly toxic. Air-conditioning is another system that may come with special winterizing recommendations from the manufacturer. Before you start the winterizing procedure build a boat winterizing kit pick up a few gallons of RV antifreeze a can of fogging oil motor oil an oil filter lower-unit lube and drain plug gaskets an oil suction pump and a lower-unit lube injection pump.
Then gather up your screwdrivers sockets and combination wrenches. Prepare Your Inboard Boat Motor for Winterizing. Fill the tank with gas.
Add Antifreeze and Spraying Fogging Oils. After your motor is cleaned and prepared as described above the first real winterization step is applying antifreeze. Change the Engines Oil.
Warm and mix the oil for changing and flush the cooling system if you have been running in salt or brackish water. After running change oil filter. Change fuel filters be sure to check the contents of the filter.
If there is around a 14 of the contents water you should drain the water out of the tank. That wont be covered here 4. This is where the act of Winterizing comes into play.
This is essentially the process of preparing your boat for the winter. There are quite a few things which this process involves such as flushing your engine draining the boat of all fuel and fluids disconnecting electronics washing the boat and more. Prepare Your Inboard Boat Motor for Winterizing.
Fill the tank with gas. Add Antifreeze and Spraying Fogging Oils. After your motor is cleaned and prepared as described above the first real winterization step is applying antifreeze.
Change the Engines Oil.