How to paint an outboard motor

I have to admit that these engines get gunk all over them. Give your outboard new color with the Quantum 2K kit.

Part 1 of 4 Johnson 90 hp If playback doesnt begin shortly try restarting your device.

How to paint an outboard motor. How to paint an outboard motor. Part 1 of 4 Johnson 90 hp - YouTube. How to paint an outboard motor.

Part 1 of 4 Johnson 90 hp If playback doesnt begin shortly try restarting your device. Painting Your Outboard Motor. Give your outboard new color with the Quantum 2K kit.

A heat gun or blow dryer is helpful in loosening old decals but be careful not to overheat and damage the fiberglass cowl and shroud. Use denatured alcohol to remove the adhesive residue. Remove the outboard motor from your boat and place on your painting work surface.

Sand the entire outboard motor using 400-grit wet sandpaper. Sand the motor down to its bare metal surface. If you wish to protect any existing decals on the motor cover them first with Painters tape before sanding.

Typically if you have only sanded the factory paint and not exposed bare metal you can paint right over it without priming. As you did with the cowl spray the factory enamel until at least two coats are applied. Turn on CCSubtitles for added details about the processHere you see the complete process of touching up the paint on the top cowl of a Johnson 200 which.

Clean and prep the lower by removing any and all paint preferably get it to bare aluminumeither by sanding or using a chemical type stripperbe careful not to damage any of the seals. Then use a good quality Zinc Chromate primer under your choice of primer and paintpreferably good quality marine paint but others have used everything. The most basic features are a nozzle that allows a change in spray pattern by rotating the nozzle on the front of the gun.

There should be a knob to control with of the spray pattern and finally a way to adjust the needle to control the amount of materialpaint that can come out of the gun tip by pressing the trigger. If it is a smooth glossy surface you will need to rough sand to get the paint to adhere- I would clean it real good- degrease any oily places- prime and paint if you are worried about it flaking off- -if it is a run of the mill duck boat just skuff up the shiny spots prime it and spray bomb the hell out of it and retouch as needed- buy the flat camo paint. The secret to painting is patience.

Dont try to cover the area in one coat. Spray on several light coats perhaps six or more to build up a drip free primer coat that completely covers the old surface. Follow the directions on the paint can especially those about shaking and mixing the paint before and during use.

It is painted with car paint. You just need to fill the scratches and then sand it. The decals should go on after the paintjob.

Reprotint outboard motor paint. I have to admit that these engines get gunk all over them. 1 800 432 8344 or 1 931 738 8090 fax.

Moeller marine products 801 north spring st. Mainly from having to repaint the cowl a couple times messing up the 3 tone or 2 tone lines. Reprotint is an extremely high quality single stage acrylic enamel with outstanding.

These outboard engine paints are fast-drying with easy application. They are gasoline oil and heat resistant made to help extend the life of your engine. Moeller paints are also coordinated to match your outboards OEM colors.

Interlux is a name you can trust in marine engine paints. Yamaha Outboard Engine Cover Spray Can Painting - YouTube. Yamaha Outboard Engine Cover Spray Can Painting.

Make your outboard motor look brand new. Your outboard will be completely prepped and sanded down to the needed workable surface. All minor scratches or imperfections will be corrected so that the motor looks flawless like it came straight from the factory.

Contact us to get more information on this and other services we provide. Please like and comment. I had very good luck with the rattle-can anitifouling paint on my Honda outboard.

I just sanded the old antifouling paint once over lightly with some 80-grit paper and sprayed. After the power wash in the fall the lower unit of the engine looked as good as or maybe even better than everything else below the water line. Inboard Outboard Engine Paint How-Tos.

The lower unit is where the gears are. Thats what turns the prop its where the exhaust comes up some of the motor picks up the water. And the problem with the lower unit is being down so low is it wants to hit the bottom.

Get your paint shake it for 2 minutes and warm in hot water for 2 minutes. Apply a light coat covering all areas and ensuring it does not drip. One of the biggest problems with this step are dirty oily spots.

Outboard motor paint colors - To observe the image more obviously in this article you are able to click on the wanted image to watch the photo in its original dimensions or in full. An individual can also see the Outboard Motor Paint Colors image gallery that we all get prepared to locate the image you are searching for. This first paint is a Johnson Evinrude paint specifically.

And its the paint according to this that was used between 1981 and 1991. I think this outboards a 94. Whether you need a cowling repaired or you want to repaint those triple 300s The Outboard Paint Shop has you covered.

Just give them a call and tell them that Coastal Angler Magazine sent you.