How to mount a bow mount trolling motor

In this method of mounting the shaft of the motor has a plastic or composite block that clamps onto the stainless steel railing as close to the centerline of the boat as possible. An electric trolling motor designed to be mounted on the transom can also be mounted on the bow of a V-hull boat or adapted for backtrolling trolling stern-first by taking out the screw and nut at the base of the motors.

I really want a bow mount trolling motor but have a mounting question.

How to mount a bow mount trolling motor. Putting a Minn Kota Powerdrive V2 bow mount trolling motor on an Alumacraft 1860 aluminum jon boat. How to Perform Bow Mount Trolling Motor Installation - Minn Kota Terrova Ulterra Ultrex - YouTube. Leave the mounting base in place and pull the shaft up.

Lay the motor down on the deck in the stowed position. Make sure the motor head is inside the perimeter of the boat so it wont be damaged when you dock the boat. An electric trolling motor designed to be mounted on the transom can also be mounted on the bow of a V-hull boat or adapted for backtrolling trolling stern-first by taking out the screw and nut at the base of the motors.

How to Mount a Trolling Motor Bracket on Bow. Bow mounting of a trolling motor allows effective navigating of the vessel while spending less effort. One usually installs the main motor on the opposite side because trolling motors are often used when the main motor is.

Now if you choose to have a bow mount trolling motor and anchor nest at the same time you will want to make sure that when your bow mount trolling motor is in the stowed position that the shaft not only clears your Anchor Caddie and anchor it also stows off to the side and not obstructing the bow as shown on Louis bow below. If you plan to have a bow mount trolling motor. If you dont want to remove the bowrail heres a neat way to get around it.

The owner cut a piece of the bow rail off big enough to allow the troll motor to pass through and extend and replaced the section with a piece of SS tubing with an inner dimension slightly larger than the outer dimension of the bowrail then added some quick release pins. Mounting bow mount trolling motor on 14 v-hull. By bcbouy 02 Apr 2018 0031.

550 plus 60 canadian for a quick release mounting plate and a hand held remote is includedwith a lion rechargeable battery55 lbthrust and a built in battery gaugehad it for 2 years with no problems whatsoevercould buy 3 of them for the price of the. Installing a bow-mount TM on my old tri-hull. The bow has large flat areas on either side of the redgreen nav light plenty of room to install the quick-release bracket.

The only concern is that I have no access to the underside of that area so I. New to the whole scene here. I just purchased a Grizzly 1648 MVX.

It will have electric motor only as you cant even have a gas one mounted for the reservoirs around here. I really want a bow mount trolling motor but have a mounting question. On the grizzly I would not be able to get to the underside of the bolts to lock up with a nut.

There are many ways to mount a trolling motor on your bowrider the simplest and least expensive being the screw-clamp-on-the-bow-rail style. In this method of mounting the shaft of the motor has a plastic or composite block that clamps onto the stainless steel railing as close to the centerline of the boat as possible. How to mount a trolling motor on an aluminum boat is very simple.

For a transom mount motor after you position your motor correctly you only need to tighten the clamps. For a bow mount trolling motor you will bolt the motor mount through the deck with or. 1 Slide the decket off of the mount base.

2 Select the area on the boat deck to install the mount. Choose an area with enough room to allow the motor to be in both running and storage positions. Allow for 2½ to 3 inch clearance between the shaft and the bow of the boat to allow room for the mount to break-away flex and protect the motor.

You drill the hole push in the well nut place the motor or mounting plate over the well nuts and then insert and tighten the bolts. No need to get under the deck and the rubber flange keeps the motor off the glass. Smaller boats may not have enough room to fix a trolling motor on the bow or transom.

Place the Mount on the Outboards Anti-Ventilation Plate. Before you buy the trolling motor you should check if the plate is deep enough under the waterline. There should be minimum 13 inches of submersion for the trolling motor to function correctly.

That way the handle is pointing toward you. After you have put the motor together the second step is to attach the shaft. Once in place you can install the head assembly to the mount.

Positioning the Trolling Motor. You should position the motor shaft as close to the middle of the boat as possible. One thing to pay attention to is that the shaft and propeller may become off-center.