How to make a motor mount for inflatable boat

What if you want to hang your dinghy from the back of your yacht and keep your motor vertical without removing it. Then customer used electric conduit pipes to cut out structure to hold wooden board to act as a motor mount.

Classic Accessories Colorado Inflatable Boat comes with a motor mount for trolling.

How to make a motor mount for inflatable boat. Common wisdom dictates that in the center at the rear of an inflatable boat is the best place to mount a motor. I tried this option but is became complicated. The structure was fiddly to put together and the motor was far away meaning I had to devise an extended steering mechanism as well.

The simplest inflatable boat motor mount system is to simply set it on the transom and tighten up the clamps. Ahhhhh if it were only always this easy. What if your motor sits too low.

How can you tell if it is too low. What if you want to hang your dinghy from the back of your yacht and keep your motor vertical without removing it. That was done so that to have electric trolling motor mount in an inflatable boat front.

First four glue-on black holders were glued to bow area. These can be found on Amazon or Ebay. Then customer used electric conduit pipes to cut out structure to hold wooden board to act as a motor mount.

Conduit elbows were used to join pipes together. This is for a Intex Seahawk 2 but the same principle applies for different boats. Israel My thoughts on making your own motor mount are along the same lines as thezster.

You would not want to be out in the water and have any kind of failure. I personally would only use the accessory motor mount that is made for the boat model you have and by the same mfr. Then design a mount of galvanized pipe that latches or straps onto those patches and finally an extension of the pipe that holds a plywood transom plate as low as possible.

It shouldnt be that hard to do as long as you were designing the thing for a small under 5hp motor. This is trivial but still something to consider. The greater the airpressure in the inflated chambers the stiffer the vessel will be.

Determining the air pressure to use will come from a combination of material strength and size of the chamber. Also the right side of the motor mount was sunk into the floor about 14 inch. The bolt going through the motor mount into the floor was up off the mount about the same 14 inch.

Aware of the likely result I tried to tighten the bolt. As expected I could hear the stringer below crunch as the wood crumbled. I had the boat out on two occasions for engine tuning and adjustments.

Intex Motor Mount Kit. Heavy-duty composite and aluminum supports. Easy to attach to the back of a boat.

Fits up to 30 HP motors. Fits Intex Seahawk 2- 3- and 4-person boats. Fits Intex Challenger 3-person boat Intex Excursion 3- 4- and 5-person boats and Mariner 3- and 4-person boats.

Motor mount kit could be instalated on the bow of the inflatable boat or on the stern of inflatable boatfor inflatables without transom. Removable bow or stern motor mount can be used for many fishing accessories. Inflatable boat motor mount dimensions - bow or stern.

Motor mount kit outboard bracket Sale Price. Take ePropulsion 3 hp electric motor for inflatable boats with integrated battery as an example there are 5 easy steps to get started. Attach the motor to the stern of the inflatable boat with the clamp no tools required.

HI everyone this video will show you how I made a trolling motor mount for my 2017 Ascend 128T Kayak. The whole project cost less than 25. Less than an hou.

Its also completely safe. Your inflatable boat wont get scratched or damaged thanks to the smooth design of this motor mount. Made for inflatable boats this motor mount is super easy to install.

You can install this on various outboard motors. Dont have loops on your stern. You can buy a mounting bracket clip to solve this problem.

Step by step instructions for how to build a front mounted trolling motor mount for the Colorado XT pontoon boat. This is part 1 of a 2 part video. Saved by Kelly Grant.

Pontoon Trolling Motor Kayak Trolling Motor Mount Inflatable Pontoon Boats Small Fishing Boats Boat Stuff Canoe Kayaking Baby Strollers Colorado. Intex Composite Boat Motor Mount Kit For Inflatable Boats. Intex is a brand that knows how to create products for the water and thats definitely the case with their Composite Boat Motor Mount Kit.

This kit has been specifically designed to mount a motor to an inflatable boat and it suits a. 5 out of 5 stars. 108 108 product ratings - Intex Composite Support Boat Motor Mount Kit for Inflatable Fishing Boat or Raft.

Intex 5 Person Inflatable Fishing Boat Trolling Motor Boat Motor Mount Kit Product Description Features. Intex Excursion 5 Inflatable Boat Set Intex 12V Read more YUEWO Trolling Motor 34506065LBS Thrust Transom Mounted Saltwater Kayak Electric Boat Motor with 9 Levels of Colorful Power Display and 8 Variable Speed for Inflatable Fishing Boats. Classic Accessories Colorado Inflatable Boat comes with a motor mount for trolling.

If you love fishing then this boat is likely the best choice. Its especially useful for fishermen because it has a rod holder which you can mount in three different positions on each oar stand. In this video I turn an inflatable row boat Intex Excursion 5 and modify it into a fishing boat.

I walk you through step by step of how I make this boat as. Investigating further I noted a rounded metal rod based mount on an inflatable RHIB that looked like a modified fender holder with some marine-ply bolted on for the motor mount. The curve of the metal rods fitted well around the hull of the RHIB and appeared to.

On a short shaft outboard engine the prop is around 6 inches shorter in comparison with the shaft on a long shaft engine enabling you to get closer to the shoreline and use your dinghy in shallower waters which is particularly useful if you are using your dinghy as a tender from a larger vessel to the beach. Where should my outboard sit in the water. When positioning your outboard engine on your inflatable.

An electric trolling motor designed to be mounted on the transom can also be mounted on the bow of a V-hull boat or adapted for backtrolling trolling stern-first by taking out the screw and nut at the base of the motors control unit rotating the control unit 180 degrees and then replacing the screw and nut without damaging the motor wires.