How to convert a tiller outboard motor to steering

At the end of the tiller is a handle that can be twisted to adjust the motors speed. You can install a Auxiliary motor steering kit between the 115 and the 99 for steering 99 have a choice of.

Also need two 877773A__ replace __ with length cable needed Regards.

How to convert a tiller outboard motor to steering. Push the cable through the outboards tilt tube – the tube on which the engine tilts up and down. Attach the end of the cable to the motors steering arm or steering link rod. Using the steering arm or link rods bolt and lock nut.

Tighten to 20 foot-pounds with a torque wrench. Converting from tiller to wheel allows you to move forward in the boat. When you decide to convert the tiller steering on your outboard to helm-type steering with a steering wheel the most important part of the project is testing.

A boats steering system must work correctly and easily every time. Click to see full answer. It may well be better to get an EP electricremote model rather than converting your tiller model.

If you are presently pull start only and want to convert to electric start add that cost for starter motor and all the associated bits in as well. The actual process depends on the kind of steering. The easest way would be jut to install steering and tthottle controls you will have to go back and pull start your motor then run it with the shifter and thottle controls wishin i.

I bought a Mercury 25hp tiller steer motor and converted it to remote control by buying a ready made kit from mercury but i cant remember how much it cost i think about 200 this didnt include the remote levers or the cables which i already had just the engine fittings which cost me 50 to be fitted so it cant be that hard. RemOh Yes this sounds highLets try to break it down in stagesYou need a kit to remove the tiller handleand install hardware to mount a steering cable to your motorNow you need another kit to enable the shift cable and throttle cable to mount and work on the engineA wiring harness needs to go up frontalong with two control cablesNext needed is a control box to connect this toNow we need a place to mount itA steering cable would be niceand connect. Right now its got a great running electric start 25 horse power Mercury mid 90s on the back that is tiller steer.

There is also a tiller steer trolling motor mounted back there. Its just really cramped and hard to fish around and troll. Im looking into converting it to stick steer and getting a foot controlled trolling motor mounted up front.

Main reason is it has the tiller handle on it so if the guy the buys it is running a wheel it is simple to remove the tiller arm and convert to a counsel. My main concern is being able to keep the power steering and the hole shot. Now my boat jumps up out of the water.

Figure about 300 for the steering link and cables. A no-feed back steering for the one I did cost 157 plus 1180 shipping without a wheel. It adds up but it sure is nice when making a long run in cold or rough condidions.

Push on the end of the tiller handle and the valve opens allowing you to steer. Pull on the end of the tiller handle and the valve opens allowing you to steer. Rest your hand on the tiller and the valve remains closed locking out the propeller torque and providing comfortable boat operation.

Run the line from the OB thru the tubing to the tiller the tubing acts as a strong arm between the Engine and tiller the line connect the two then run the line from the Tubing thru a eye strap to a cam cleat to secure. Pull the line tight and you have a linked tillerengine release the line and the tiller is free to operate independantly. Getting to Know Outboard Motors There is also a hinge that allows the motor to turn from side to side freely and a lever called the tiller extends into the boat to be used to turn the motor and steer the boat.

At the end of the tiller is a handle that can be twisted to adjust the motors speed. Have you ever wondered how to use a tiller steer outboard engine. You can move side to side in the river by using your kicker motor which allows you to cover all the water in a hole or the tail-out above a riffle.

If you are using a remote controlled motor where the steering wheel with shiftingthrottle controls are forward the skipper. F15ESHC Need help with conversion from tiller to console remote. Hi all I picked up a nice little 2004 Lowe MV1462 with a F15ESHC.

Its in like-new condition not sure its past 10 hours yet. The price was right and I think its worth converting to console steering remote throttle for better balance and visibility. Use the engine-mounted shifter to shift in and out of gear.

Each brand is a little different in this regard but most are located on the front of the motor on the opposite side of the tiller. Twist the tiller to accelerate and decelerate. I have a Outboard jet - 0R240539 F25ELHJet- that is tiller steer.

I want to convert it to consol steering and throttle. I have a 1999 trophy bayliner model 2002 with a 120 hp Mercury force outboard motor I want to buy a 99 hp kicker motor for trolling can I install a tiller motor on the back of boat next to other moto. Converting 15hp from tiller to remote Hello I am a new member who wants to convert my 01 Yamaha 15HP 15MSHKZ from tiller to remotewheel steering.

I have a console steering wheel but need to know what part to buy to connect steering and engine controls to the motor. There is no motor tilt or starting involved. If this a two stroke 99hp then you would need.

42805A 6 REMOTE CONTROL ATTACHING KIT to convert motor to remote control operation. You can install a Auxiliary motor steering kit between the 115 and the 99 for steering 99 have a choice of. 892763A13 Zinc steering kit or.

892763A16 Stainless steel steering kit. You need 67701-94L00 drag link when you will use tilttube steering and 67130-94L00 remote kit see picture. The last one is quit expesive at least in europe then you need a remote controle box and two cables.

The remote conrole box can be anything as long as it is push to open en fits C2 C33 cables and steering parts. The tiller is another name for a control handle on an outboard motor. Tillers are common on fishing boats and can be used in both freshwater and saltwater.

Here are tips to help you steer with the tiller in reverse. To reverse in a straight line set the tiller so that its handle points directly to the bow. Keep the power low and the tiller in a straight line.

To reverse to the left turn the tiller to the right. The Optimus system consists of two primary components. First the electric actuator at the stern that connects to the outboard one per engine and second the electronic drive-by-wire helm unit to which the steering wheel mounts.

The electric actuator turns the motor by spinning roller screws inside the threaded body of the actuator. 826633A 1 Remote Conversion Kit. 95723A 4 Engine electrical harness.

881170A 5 Side mount Control box elect start no trim. Also need two 877773A__ replace __ with length cable needed Regards. Despite these minor changes the components of most outboard motors are the same.

The motor attaches to the back shelf of a boat and can be raised and lowered into the water on a hinge. There is also a hinge that allows the motor to turn from side to side freely and a lever called the tiller extends into the boat to be used to turn the motor and steer the boat. At the end of the tiller is a handle that can be twisted to adjust the motor.