01
Aug
Use a funnel to pour the B12 carb cleaner into the tank so the paint isnt ruined. Make sure that you dont spray below the throttle plate.
This is used to drain down the bowl when the carburettor is on the engine.
How to clean carburetor on outboard motor. How-To-In-A-Few video on cleaning the carburetors on an outboard boat motor. Get that engine running smoothly and starting on the first crank. How To Clean an Outboard Engine Carburetor - YouTube.
An excellent way to clean an outboard carburetor without removing would be by using the Berryman B12 Carb Cleaner. First blend 4 oz of the B12 with a full gasoline tank. Use a funnel to pour the B12 carb cleaner into the tank so the paint isnt ruined.
Note the screw with the spring which can be seen at the top. This is used to drain down the bowl when the carburettor is on the engine. The bowl when removed can be thoroughly cleaned of any debris or residue.
Note the locking nut has a washer so carefully retain this or replace if necessary. However surprisingly few boat owners know how to diagnose and fix the problem. So when I saw the article about cleaning the carburetor of an outboard engine in Practical Boat Owner I knew I had to share.
David Parker describes in detail with color pictures how he saved a lot of money with a careful strip-down and clean of the carburetor. Taking Out the Air Filter. At least on the motor we are working on which is a 1958 35hp Johnson the carburetor is buried behind the air filter.
After unscrewing and taking out the face of the motor you will take the air filter out in two steps. First the intake plenum as shown in picture then after removing the mixture adjustment. Unblocking Outboard Carburetor Jets In this video I show a quick trick for unblocking a carburetor jet in the field.
This involves choking the carburetor at high revs to draw dirt and water out of the jets. How do you clean outboard carburetor without removing. An excellent way to clean an outboard carburetor without removing would be by using the Berryman B12 Carb Cleaner.
First blend 4 oz of the B12 with a full gasoline tank. Then go for a slow ride so the carb cleaner flows through the idle system. How do you drain a carburetor on an outboard motor.
No chemical cleaner can take the place of actually cleaning the carb by hand. You have to pull the jets and run a copper wire through them to get them really clean chemicals will break things loose and usually clog a passage. As weve established the primary way of cleaning outboard carbs with no removal is using a carburetor cleaner.
To clean an outboard motor and carb you add the cleaner to a full gasoline tank run the motor for a bit and check the results. If necessary rebuild your carb. In the end we hope that our guide on how to clean outboard carburetor without removing it provided you with helpful insight into.
The carburetor of outboard engine is simple in structure and saves many parts. Its lighter and easier to maintain than the equivalent four-stroke outboard engine but it doesnt have the same fuel economy as the electric jetIf compared with the ordinary words fuel consumption the same horsepower under the four stroke electric injection machine than two carburetors save 30 or so. When cleaning with the engine running spray on both ends of choke valve shaft while working the choke with hand.
Spray around the throat of the carburetor to eliminate the deposits from throttle plate area. Make sure that you dont spray below the throttle plate. There are some components that must be avoided while cleaning with the spray.
Remove the motors top cover. Pull up on the Fast Idle control. Spray the Power Tune into the carburetor throat.
Shut the motor off. Remove the spark plug wires by twisting them and pulling straight up. Remove the spark plugs with a plug wrench.
Remove the fuel line from the engine as well as the one to the outboard carburetor. Inspect the engine for any other wires or connections that lead to the carburetor and disconnect them as well. The outboard carburetor is bolted to the intake manifold.
Choose the correct ratchet and remove. Spray carburetor cleaner through the upper air-intake jets on the carburetor body. Observe the air ports in the carburetor barrel to ensure that the carburetor cleaner is.
Cleaning mix into the carburetors. Allow engine to sit and soak Overnight to 24 hours if possible 48 to 72 hours when necessary. Once the engine starts and runs Sea Foam in the tank will continue to dissolve residues as fuel is drawn through the carburetor.
Add more fresh fuel when ready to operate engine under load working engine. How do I clean my seafoam outboard carburetor. After removing gasoline from the tank and carburetor add a mixture of Sea Foam followed by 8 ounces of fresh gasoline 1 to 2 ratio.
With the cleaning mixture in the fuel tank crankprimerope-pull the engine to draw the cleaning mix into the carburetors. Click to see full answer. After rebuilding these carburetors I still had a rough idle.
I took the carbs back off and removed the access plug and carburetor lead shot to clean the idle circuit out completely. I also found a good alternative to the expensive carburetor lead shot plug from OMC JohnsonEvinrude. This is my second go around with these carbs.
Position the tip of the aerosol can into the center of the carburetor and spray directly into the running carburetor. Doing this while the carburetor is running allows the cleaner to penetrate inside and clean the carburetors throat and remove deposits that exist in the lower throttle plate. Secondly how do you adjust the carburetor on an outboard motor.
How to Adjust Carbs on an Outboard Motor.