Changing oil in lower unit of outboard motor

First be sure your outboard is in a vertical and upright position. The last time the oil was changed was probably 6 or 7 years ago when the water pump was changed and a new powerhead was installed.

After all without the proper Mercury 2 stroke oil the internal of components of the motor.

Changing oil in lower unit of outboard motor. 40 rows into the BOTTOM drain hole. Then slowly squeeze the bottle to force the oil into the lower. When the refilling is done tighten both plugs with your hand and clean any oil spill on your lower unit.

Always make sure that your lower unit is filled with enough before you operate your outboard because if not it can cause serious damage that will cost a lot of money to repair. Checking the oil level is not difficult pretty much like checking the oil of your car. How to Change an Outboards Engine Oil.

After buying the oil and a new oil filter get a wrench or flathead screwdriver some shop towels or rags and a drain pan. Run the outboard for a minute before changing the oil to warm the used oil which makes it less viscous and helps it drain out faster. I have a 15hp Chrysler Outboard.

I want to change the oil in the lower unit but i cant find an oil pump fitting that will fit my engine. I was wondering if you HAVE to use the pump or can you just drain it put the bottom screw in and just fill it from the top screw hole till it starts pouring. Changing your oil is a type of preventative maintenance that will help keep your outboard lower unit in prime shape so long as you keep up with it.

At the bare minimum you should change the oil out at least once a year and that can be enough for people who only occasionally use their boats. Into the BOTTOM drain hole. Then slowly squeeze the bottle to force the oil into the lower unit.

Continue adding oil until the lubricant is flowing freely from the top hole and is free from air bubbles. Keep the bottletube in the bottom plug or plug the hole with your finger and re. In this video I am doing the break in service on this new Yamaha F300XCA.

We will be changing the engine oil and the lower unit oil. Changing the Lower Unit Oil The lower drainfill plug screw is usually located on the starboard side of the lower unit beneath the bullet-shaped portion of the lower unit housing. Locate your drainfill plug screw and adjust the trimtilt of your outboard motor or sterndrive so that this plug is in the lowest position possible in order to drain the used oil thoroughly.

Changing Lower Unit Oil in an Outboard Published on April 8 2016. Last updated on April 4 2021 by Carolyn Shearlock If you have an outboard on your dinghy youre going to have to periodically change the lower unit oil. To start simple loosen the bottom screw on the lower unit and make sure the oil pan is underneath before loosening the top screw.

Once you loosen and remove the top screw the oil will drain very quickly into the pan. I usually wait about 10-15 minutes to allow all the oil to drain before attaching the gear oil pump and adapter. After placing the drain pan below the lower unit remove the lower screw.

Oil will begin slowly draining out. Next remove the upper screw. This will allow air to flow into the lower unit displacing the oil and the remainder will drain out quickly.

Tilt the drive unit up a bit if necessary to be sure all the oil drains out. Lower Unit Oil Change. First be sure your outboard is in a vertical and upright position.

Locate and identify the upper and lower Fill Drain Plugs. Place an oil drain pan beneath the outboard. Remove the BOTTOM drain plug first not the top.

Winterizing Outboard Motor Lower Unit. October 14 2021 by masuzi. Changing lower unit gear oil winterizing your outboard motor west how to winterize your outboard motors outboard winterizing.

Winterizing Outboard Changing Lower Unit Gear Oil Fast Easy You. A rule of thumb for the models that require the HD Gear Oil is the oil filter. If the engine uses a N26-13440-02-00 oil filter or a N26 for short.

Then that engine requires the HD Gear Oil which is to the left and is also a brownish or yellowish color. It is extremely important that you get the right gear oil into the lower unit that you have. Changing the motor oil in the lower unit of a Mercury outboard is a fairly simple task.

All responsible boat owners should at the very least know when to change the oil. After all without the proper Mercury 2 stroke oil the internal of components of the motor. Time to change the oil in the lower unit of my Evinrude 30 horsepower outboard motor.

The last time the oil was changed was probably 6 or 7 years ago when the water pump was changed and a new powerhead was installed. While my wife and I were in Jasper Texas taking care of some business we stopped by the Evinrude dealership and got some gear oil.