Bow mount trolling motor shaft length

Bow Mount Shaft Length For freshwater your minimum required shaft length should be 20 from the bow to water line. In other words the centerline of the motor and the prop shaft should be about 12-18 inches below the waterline depending on the make model and dimensions of the trolling motor.

Bow mount trolling motor shaft length.

Bow mount trolling motor shaft length. How To Correctly Measure Bow Mount Shaft Length Freshwater. Bow to Water Line 20 Minimum Required Shaft Length. Bow to Water Line 25 Minimum Required Shaft Length Transom Mount Shaft Length.

Shaft length on transom mount motors is less critical than on bow mount motors but is still important to double-check. Trolling Motor Shaft Length Measurement Tips. Choosing the correct trolling motor shaft length is important so that the anglers electric motor does not cavitate creating fish-spooking noise.

The rule of thumb is that the top of the motor section should be submerged 12. In general shaft length selection is more critical with bow-mount motors versus transom-mount motors. Bow mount trolling motor shaft length.

Im going to buy a bow mount trolling motor for my boat this year and I want to know if I need a 52 or 62 inch shaft. The boat is a 1890 Warrior Tiller I have a 75 pound thrust transom mount motor also. I am looking the 74 Minn Kota Maxxum.

Bow Mount Shaft Length For freshwater your minimum required shaft length should be 20 from the bow to water line. For salt water your minimum required shaft length should be 25 from the bow to water line. Here are the recommended shaft lengths.

Transom Mount Shaft Length. Bow to Waterline Recommended Shaft Length 0-10 36 16-22 42-45 22-28 48-52 28-34 54-62 Id like to addis anyone selling a used one. Preferably 55lb Edited May 27 2014 by finatic Roy Administrators 137k Male Boucherville QC.

Posted May 27 2014 Mines always between 42 - 45 and Ive never run out of water yet. The 60 inches may not be used all of the time but if you get out in any wave the motor wont be popping in and out of the water. It wont hurt to have the extra shaft length.

In rough water the prop would come out of the water on nearly every wave peak. That was a real pain. Now when I buy a trolling motor I buy the longest shaft I can get in a 24-volt motor.

And yes it was well worth the day it took me to rig up my Magnum for 24-volts including re-inforcing the bow deck for the extra stress. I have a 219FS however I had a 60inshaft mounted on a 186 sportsman so I guess the 219 should handle the 72in. Thanks for all your help.

Sent from my SM-N950U using Tapatalk. The front deck where I want to mount the trolling motor is ABOVE the gunnels and the top of the gunnels were even with the transom. It does seem a shame that a guy can buy a good used boat with a 15 to 25 hp internal combustion motor for around 5000.

Then a remote controlled trolling motor costs 50000 to 150000. Shaft Length for Transom Mount Motors. If you want a trolling motor that mounts on your transom things are usually less complicated.

This is because most boats have transoms at a similar height. Minn Kota recommends the following shaft length for different transom heights. 30 shaft for transoms up.

This is a bow mount trolling motor shaft length formula. Height x 15 depth in water shaft length When you use this formula height is the measurement you took from the mounting location to the water. Depth in the water is the standard twelve inches plus the allowance for water conditions.

What shaft length for bow-mount trolling motor I have a LT15 with a Minn Kota Riptide bow mount on the nose piece. The model is RT55BH with a 52shaft. The prop sits a good foot under the water line and the handle is at a perfect control height I am 5 10.

No complaints at all. In other words the centerline of the motor and the prop shaft should be about 12-18 inches below the waterline depending on the make model and dimensions of the trolling motor. To calculate the ideal shaft length for your boat select the point on the transom or bow where the motor will be mounted then measure down to the waterline.

80 54 Shaft Length 80 lbs Thrust 24V Trolling Motor with i-Pilot The Riptide Terrova 80 has a lift assist design which raises the motor by barely lifting a finger. It also comes with a push to test Battery meter and a weedless wedge 2 Prop. MotorGuides shafts come in various lengths ranging from 30 to 72.

MotorGuide Technology and Features MotorGuide has been designing and manufacturing trolling motors for over 50 years. Today they are built with aircraft-grade aluminum mounts and stainless steel bushings. This helps increase rigidity and reduce material wear.

Joined Apr 26 2012. Discussion Starter 1 8 mo ago. I am looking to put a new bow mount trolling motor on my Alumacraft Trophy Deep V boat.

It presently has a 54 which only stays in water on calm days. Clearly needs at least 60 but wondering if any of you are using the longer 72 to get a better bite on days. Edge 12V 45 lb Thrust 36 Shaft Bow Mount Freshwater Trolling Motor 1355946 by Minn Kota.

Dont let the size fool you. Edges compact mount is built with extruded anodized aluminum for rugged no-nonsense strength. 186 CC Trolling Motor Shaft Length Question.

Post Mar 06 2012 1 2012-03-06T2120. First of all this is a great site. So glad I found it.

Assuming its a bow mount the logical access to bolt it on is through the anchor locker. On some models you simply reach under the deck and put the nuts and. If you decide to place the trolling motor on the bow youll require a long shaft length the reason being that the bow is always a bit higher when compared to the boat.

Typically the standard shaft length on the market is 42 inches. Generally speaking the average shaft length for a trolling motor is around 60 or 152cm if you intend on mounting the motor on the bow of your boat. While this is a good rule of thumb there are other things to consider when determining this length.

If you really want to play it safe you can choose a 48 shaft for your trolling motor.